JD 5325 Engine Specifications
Engine Type – 5030 Diesel
Cylinders – 5
Aspiration – Turbocharged
Lubrication – Full pressure, full flow filtration
Displacement – 3.0 L (184 cu. in.)
Bore – 86 mm (3.39 in.)
Stroke – 105 mm (4.13 in.)
Compression Ratio – 18.0:1
Cylinder Firing Order – 1-2-4-5-3
Slow Idle Speed – 900 ±50 rpm
Fast Idle Speed – 2625 ±50 rpm
SAE Gross Engine Horsepower – 50 kW (67 hp)
PTO Horsepower (Factory Observed) – 41 kW (55 hp)
Rated Speed – 2400 rpm
Fuel Injection Type – Integrated Fuel System (IFS) Integral with
Cylinder Block
Air Cleaner – Dry-type, Primary and Secondary Elements
Cooling System Type – 69 kPa (0.7 bar) (10 psi) Centrifugal Pump
Fan – Viscous Drive
Thermostat – Single
Electrical System Type – 12 volt, negative ground
Battery Voltage – 12 volt
Battery Cold Cranking Amps – 925 (5 Cyl.)
Reserve Capacity (minutes) – 180
Battery BCI Group Size – 31
Alternator – Open Station: 70 amp / Cab: 90 amp
John Deere 5325 Power Take-Off
PTO Type – Standard: Fully Independent, Shiftable (540/540E) / Optional:
540/1000 rpm
Speed-540E – 1700 engine rpm
Speed-540 or 1000 – 2400 engine rpm
Size – 35 mm (1-3/8 in.)
Clutch – Electro-Hydraulic Operated
JD 5325 Mechanical
Basic Transmission – 12/12 PowrReverser with EH Hitch, EH PTO (shiftable
540/540E)
Optional Transmission – 24/24 PowrReverser with EH Hitch, EH PTO
(shiftable 540/540E)
Type – partially synchronized
Gears – 9 forward and 3 reverse
Clutch – dry disc
Chassis – 4×2 2WD / 4×4 MFWD 4WD (optional)
Steering – hydrostatic power
Brake Type – Hydraulically operated wet disk, self-adjusting,
self-equalizing
John Deere 5325 Hydraulic System and Hitch
Hydraulic Type – Open center, tandem gear pump, hydrostatic power
steering
Pump Displacement-Steering – 10.0 cu cm (0.61 cu in.)
Pump Displacement-Implement – 22.9 cu cm (1.40 cu in.)
Steering Flow Rate – 22.3 L/min (5.9 gpm)
Implement Flow Rate – 51.2 L/min (13.5 gpm)
Maximum Pressure-Steering – 13000-13500 kPa (130-135 bar) (1885-1958
psi)
Maximum Pressure-Implement – 19500 ±500 kPa (195 ±5 bar) (2828 ±73 psi)
Rear SCVs – (Standard) Basic, 2-Function
Rear SCVs (Optional) – Deluxe, 3-Function, Adjustable
Optional Mid-Mount Valve with Multi-Function Control Lever – Basic,
2-Function
Three-Point Hitch Type – Top link sensing, Category IN, I and II
Standard – Draft links with adjustable ends and interchangeable balls
Lift Capacity at 610 mm (24 in.) Behind Hitch Balls – 1530 kg (3374 lb)
Capacities
Fuel Tank – 72 L (19 gal)
Cooling System – 9.5 L (2.5 gal)
Crankcase with filter – 10 L (11 qt)
Transmission-Hydraulic System – 43.5 L (11.5 gal) 12/12 PowrReverser /
45.4 L (12.0 gal) 24/24 PowrReverser
MFWD Differential Housing – 5.0 L (5.3 qt)
MFWD Wheel Hub (Each) – 0.5 L (0.63 qt)
JD 5325 Dimensions
Wheel Base (2WD) – 2050 mm (81 in)
Wheel Base (MFWD) – 2077 mm (81.8 in)
Overall Length Including Draft Links (2WD) – 3500 mm (138 in)
Wheel Base (MFWD) – 3632 mm (143 in)
Width (Outside Edge of Tires) – 1842 mm (72.5 in)
Width (Rear Axle Flange-to-Rear Axle Flange) – 1147 mm (45.2 in)
Width (MFWD Flange-to-MFWD Flange) – 1155 mm (45.5 in)
Width (Ground-to-ROPS Top) – 2408 mm (95 in)
Width (Ground-to-Folded ROPS Top) – 1946 mm (77 in)
Width (Ground-to-Steering Wheel Top) – 1615 mm (64 in)
Permissible Load Specifications
Maximum Permissible Static Vertical
Load
Drawbar Fully Extended, kg (lb) – 650 (1430)
Drawbar PTO Mid-Position, kg (lb) – 760 (1675)
Drawbar Short Position, kg (lb) – 1120 (2470)
Maximum Permissible Axle
Loads-2-Wheel Drive, With Loader
Front Tires 27/9.5-15 6PR, kg (lb) – 2430 (5350)
Maximum Permissible Axle
Loads-2-Wheel Drive and Mechanical Front Wheel Drive
Rear Tires 12.4-24 6PR, kg (lb) – 1090 (2400)
Rear Tires 14.9-24 6PR, kg (lb) – 1361 (3000)
Rear Tires 14.9-28 6PR, kg (lb) – 3230 (7120)
Rear Tires 16.9-24 6PR, kg (lb) – 3450 (7600)
Maximum Permissible Front Axle
Loads-Mechanical Front Wheel Drive Without Loader
Front Tires 8.3-16 6PR, kg (lb) – 1090 (2400)
Front Tires 9.5-16 4PR, kg (lb) – 1000 (2200)
Front Tires 10.5/80-18 10PR, kg (lb) – 2500 (5500)