JD 2054 Engine Specifications
Engine Manufacturer – John Deere
Engine Type – 6068HYH06
Emission Level – Stage III
Output – Turbo-Intercooler
No. of Cylinders – 6
Displacement – 6.8 L
Bore – 106 mm (4.19 in.)
Stroke – 127 mm (5.0 in.)
Compression – 19:1
Power at rated speed – 151 kW (205 PS)
Slow idle – 850 rpm
Engine rated speed – 2100 rpm
Fast idle – 2250 rpm
Torque bulge – 25%
Maximum torque – 878 Nm (648 lb.-ft.)
Speed at maximum torque – 1550 rpm
Injection Pump Type – Rotary
Make / Model – Denso HP3
Starter motor / Make – Bosch
Engine cooling system – water cooled – ethylene glycol or propylene
glycol base prediluted (40% to 60%) coolant
Electrical System Voltage – 12 V
Alternator capacity – 90 A
Battery / type – Sealed (unserviceable)
Battery capacity – 150 Ah (cca min. 700 A)
John Deere 2054 PTO
PTO Type – Independent
Actuation – Electro-Hydraulic
PTO Power – 128.4 kW (cv) (174 PS)
Engine speed at – 2100 rpm
Transmission and Clutch
Transmission Type – POWRQUAD
Gears – Planetary gears, hydraulic shift
Number of gears – 16 forward and 16 reverse gears.
Number of gears 20 forward and 20 reverse gears.
Clutch – Mechanical/hydraulic
Clutch Type – Oil cooled
Clutch Actuation – Hydraulic
Number of disks – 5
Diameter of disks – 225 mm (8.85 in)
JD 2054 Steering and Brakes
Steering system – Hydrostatic
Maximum pressure of steering – 18500 kPa (185 bar; 2683 psi)
Service brake – disk in oil bath
Parking brake – actuated by gear lever
Hydraulic System
Type – Closed circuit with pilot pressure
Pump – Piston Pump
Pump flow rate – 110 L/min (29.4 gpm)
Maximum pressure – 19500 – 21000 kPa (195 – 210 bar; 2828 – 3045 psi)
Control type – Electronic, with sensors in hitch arms
Selective control valves – 2 or 3
Selective control valve flow rate (100 series) – 60 L/min (15.9 gpm)
Selective control valve flow rate (200 series) – 96 L/min (26.4 gpm)
Lift Cylinder Diameter – 85 mm (3.35 in.)
Sustained Lift Capacity to 610 mm (2 ft) on hitch – 46 KN
3-point hitch type – Category 3
Hitch control – Position control,draft control,position and draft
comprehensive control
John Deere 2054 Wheel and Tires
Front – 420/85R30 (16.9R30)
Front – 420/85R28 (16.9R28)
Rear – 520/85R42 (20.8R42)
Rear – 460/85R42 (18.4R42)
Dimensions
Wheelbase – 2685 mm (105.7 in.)
Total length with front end weights – 5620 mm (221.3 in.)
Maximum Height – 2930 mm (115.35 in.)
Width rear axle (Short) – 2430 mm (95.67 in.)
Width rear axle (Long) – 2800 mm (110.2 in.)
Maximum Width (Short axle) – 2430mm/3200mm (95.66 in./125.97 in.)
Maximum Width (Long axle) – 2800mm/3750mm (110.23 in./147.63 in.)
Front tread MFWD Axle – 1440 – 2108 mm (57 – 83 in.)
Ground clearance (Rear: From ground level to draw bar) – min. 410 mm
(16.14 in.)
Ground clearance (Front: From ground level to front wheel drive axle) –
min. 523 mm (20.59 in.)
JD 2054 Capacities
Fuel Tank – 372 L (81.8 U.S. gal)
Cooling system – 28 L (7.4 U.S. gal)
Engine oil (with filter) – 19.5 L (5.1 U.S. gal)
Transmission – 80 L (21.1 U.S. gal)
Front-wheel drive axle (Standard) – 7.6 L (2 U.S. gal)
Final drives (at front axle), each side – 1.7 L (0.45 U.S. gal)