Kubota V1305 Engine Specifications
Engine Model – Kubota V1305-D18
Type Indirect Injection – Vertical, water-cooled, 4-cycle diesel
Number of cylinder – 4
Bore and stroke – 76×73.6 mm (2.99×2.90 in.)
Total displacement – 1335 cm3 (81.5 cu.in.)
Engine power (ECE-R24) – 18.2 kW (24.7 PS)
Engine power (SAE gross) – 20.1 kW (27.0 HP)
Rated revolution – 43.3 r/s (2600 rpm)
Maximum torque – 79 Nm (59 ft-lbs)
Battery – 12 V, RC 79 min, CCA 433 A
Starting system – Electric starting with cell starter 12 V, 1.4 kW
Lubricating system – Forced lubrication by trochoidal pump
Cooling system – Pressurized radiator, forced circulation with water
pump
Fuel Diesel fuel No. 2-D above 10C (14F), Diesel fuel No. 1 below 10C
(14F)
Kubota B2710 Power Take-off
Rear PTO shaft – SAE 1-3/8, 6 splines
Revolution – 1 speed (540 rpm at 2600 engine rpm)
Mid. PTO shaft – USA No. 5 (KUBOTA 10-tooth) involute spline
Revolution – 1 speed (2500 rpm at 2578 engine rpm)
Capacities
Fuel tank – 26 L (6.9 U.S.gals., 5.7 Imp.gals.)
Engine crankcase (with filter) – 4.1 L (4.3 U.S.qts., 3.6 Imp.qts.)
Engine coolant – 4.5 L (4.8 U.S.qts., 4.0 Imp.qts.)
Transmission case – 15.5 L (4.10 U.S.gals., 3.41 Imp.gals.)
Front axle case – 5.3 L (5.6 U.S.qts., 4.7 Imp.qts.)
Kubota B2710 Tires
Front – 7-12 (180 / 85D12)
Rear – 12.4 -16
Dimensions
Overall length (with 3P) – 2625 mm (103.3 in.)
Overall width (min. tread) – 1365 mm (53.7 in.)
Overall height (with ROPS) – 2334 mm (91.9 in.)
Overall height (top of steering wheel) – 1375 mm (54.1 in.)
Wheel base – 1666 mm (65.6 in.)
Minimum ground clearance – 308 mm (12.1 in.)
Front Tread – 935 mm (36.8 in.)
Rear Tread – 1050 mm (41.3 in.)
Weight (with ROPS) – 842 kg (1857 lbs)
Kubota B2710 Mechanical
Minimum turning radius 4WD with brake – 2.1 m (6.9 feet)
Minimum turning radius Bi-speed turn without brake – 2.1 m (6.9 feet)
Clutch – Dry single plate
Steering – Integral type power steering
Transmission – Hydrostatic transmission with 3 speeds range gear shift
Brake – Wet disk type
Differential – Bevel gears
Hydraulic system
Hydraulic control system – Position control
Pump capacity 3P – 24.4 L/min. (6.4 U.S.gals./min., 5.4 Imp.gals./min.)
Power steering – 11.7 L/min. (3.1 U.S.gals./min., 2.6 Imp.gals./min.)
Three point hitch – SAE Category I
Max. lift force at lift points – 830 kg (1830 lbs)
Max. lift force 24 in. behind lift points – 650 kg (1433 lbs)