JD 335 Engine Specifications
Make – Kawasaki
Engine Model Number – FH601V
Horsepower – 14.9 kW (20 hp)
Cylinders – V-Twin
Cycle – Four
Speed, Fast Idle – 3450 rpm
Speed, Slow Idle – 1775 rpm
Cooling Type – Air
Oil Filter – Replaceable Full Flow Filter
Air Cleaner – Paper Element with Foam Precleaner
Spark Plug Gap – 0.7 mm (0.028 in.)
Spark Plug Torque – 20 Nm (15 lb-ft)
Electrical System and Battery
Charging System – Flywheel alternator
Ignition – Electronic
Starter – Solenoid-shift
Battery Voltage – 12 volt
CCA – 500 amp
Reserve Capacity – 90 minutes
BCI Group Size – 51
John Deere 335 Drivetrain
Transmission – Tuff Torq K71A
Transaxle – Kanzaki
Number of Speeds – Hydrostatic, Variable Speed
Travel Speeds at Full Engine RPM (Forward) – 0-11.3 km/h (0-7 mph)
Travel Speeds at Full Engine RPM (Reverse) – 0-6.4 km/h (0-4 mph)
Front PTO – independent
Clutch – electric
JD 335 Mechanical
Chassis – 4×2 2WD
Steering – Power
Brakes – Internal Wet Disc
Cab – Open operator station. Adjustable seat with 7-inches of travel
Tires
Front Tires – 16 x 6.50-8
Rear Tires – 23 x 10.50-12
Inflation Front (Maximum) 70 – 97 kPa (10-14 psi)
Inflation Rear (Maximum) 56 – 70 kPa (8-10 psi)
John Deere 335 Capacities
Fuel Tank – 13.2 L (3.5 gal.)
Transmission Oil (With Filter) – 4.3 L (4.7 qt.)
Engine Oil (With Filter) – 1.7 L (1.8 qt.)
Engine Oil (Without Filter) – 1.6 L (1.7 qt.)
JD 335 Dimensions and Weight
Wheel Base – 1217 mm (47.9 in.)
Overall Height – 1107 mm (43.6 in.)
Overall Length – 1835 mm (72.25 in.)
Overall Width Rear Wheels in Narrow Position (Without Mower Deck) – 991
mm (39.0 in).
Overall Width Rear Wheels in Wide Position (Without Mower Deck) – 1054
mm (41.5 in.)
Net Weight (Without Mower Deck or Fuel) – 291 kg (642 lb.)
Attachments
54-Inch Mower
Mower Type – Mulch, Bag or Side Discharge
Cutting Blades – 3
Mower Weight – 61 kg (134 lbs.)
Blade Bolt Torque – 68 Nm (50 lb-ft)
Cutting Width – 137.2 cm (54 in.)
Cutting Height (approximate) – 25 to 102 mm (1 to 4-in.)
Height Adjustment – 13 position, 6.35 mm (1/4 in.) increments
48C Mower
Mower Type – Mulch, Bag or Side Discharge
Cutting Blades – 3
Mower Weight – 53 kg (117 lbs.)
Blade Bolt Torque – 68 Nm (50 lb-ft)
Cutting Width – 121.9 cm (48 in.)
Cutting Height (approximate) – 25 to 102 mm (1 to 4-in.)
Height Adjustment – 13 position, 6.35 mm (1/4 in.) increments
Position Mower Wheels
Pull out spring pin and pin. Remove gage wheel from shipping position
and install. Move mower wheels up or down until wheels are approximately
6-13 mm (1/4-1/2 in.) above mowing surface and install pin and spring
pin. Adjust all wheels to the same height, or if applicable, adjust rear
wheels to roll on the ground: To adjust wheel by 13 mm (1/2 in.)
increment, move wheel up or down one hole. Install spring pin and pin to
LOCK wheels in position.