John Deere 410G Backhoe Specs

John Deere 410G Engine

Engine Model – John Deere 4045T
Engine Type – In-line, 4-Cycle
Number of cylinders – 4
Displacement, L (cu in) – 4.5 (275)
Bore and Stroke, mm (in) – 106 x 127 (4.17 x 5.00)
Compression Ratio – 19.0:1
Aspiration – Turbocharged
Net peak power – 96 hp (71.3 kW) @ 2,100 rpm
Net peak torque – 279 lb.-ft. (378 Nm) @ 1,400 rpm
Torque rise – 23 percent
Fuel Pump – High-Pressure Common Rail
Cylinder Head – 2-Valve
Exhaust Manifold – Watercooled
Cylinder Liners – Wet-Type Replaceable
Oil Filter – Remote Access
Oil Tank – Oil Fil and Dipstick Combinations
Fuel System – Mechanical Governor
Heat Exchanger – Standard
Keel Cooled – Optional
Low Idle Speed – 700
Fuel Consumption – 26.3-29.7 L/h (6.9-7.8 g/h)
Length, mm (in) – 867 (34.1)
Width, mm (in) – 680 (26.8)
Height, mm (in) – 1055 (41.5)
Weight dry, kg (lb) – 491 (1082)

John Deere 410G Drivetrain

Transmission Type – Four-speed, helical cut gear, full powershift
transmission with hydraulic reverser
Gears – 4 forward and 3 reverse
Oil capacity – 16 qts (15.1 L)
Chassis – 2WD / 4WD (optional)
Front axle model – Carraro
Front axle type – Non-powered
Service brakes – Power-assisted hydraulic, wet multi-disc, self
adjusting
Parking brake – electric switch control, hydraulically released wet
multi-disc / Independent of service brakes
Steering – Hydrostatic power steering with emergency manual mode
MFWD Differential – limited-slip

JD 410G Hydraulic System

Hydraulic System – Pressure compensated load sensing (PCLS)
Pressure (Backhoe) – 3,625 psi (25 000 kPa)
Pressure Loader – 3,625 psi (25 000 kPa)
Flow @ 2,200 rpm Backhoe/Loader – 43 gpm (163 L/min.)
Hydraulic reservoir – Independent

John Deere 410G Backhoe Specifications

Loading height, truck loading position (Standard Backhoe) – 12 ft. 6 in.
(3.81 m)
Loading height, truck loading position (Dipperstick Extended) – 15 ft. 6
in. (4.72 m)
Reach from center of swing pivot (Standard Backhoe) – 19 ft. 8 in. (5.99
m)
Reach from center of swing pivot (Dipperstick Extended) – 23 ft. 8 in.
(7.21 m)
Reach from center of rear axle (Standard Backhoe) – 23 ft. 4 in. (7.11
m)
Reach from center of rear axle (Dipperstick Extended) – 27 ft. 4 in.
(8.33 m)
Maximum digging depth (Standard Backhoe) – 15 ft. 10 in. (4.83 m)
Maximum digging depth (Dipperstick Extended) – 20 ft. (6.10 m)
Ground clearance, minimum – 14 in. (356 mm)
Transport height (Standard Backhoe) – 12 ft. 11 in. (3.94 m)
Transport height (Dipperstick Extended) – 12 ft. 10 in. (3.91 m)
Overall length, transport – 23 ft. 11 in. (7.29 m)
Stabilizer width – transport with ROPS – 7 ft. 6 in. (2.30 m)
Stabilizer spread – operating – 11 ft. 4 in. (3.45 m)
Stabilizer overall width – 13 ft. 3 in. (4.03 m)
Width over tires – 84.6 in. (2.18 m)
Height to tops of ROPS – 9 ft. 3 in. (2.82 m)
Length from axle to axle – 82.7 in. (2100 mm)

John Deere 410G Loader Specifications

Height to bucket hinge pin, maximum – 11 ft. (3.35 m)
Dump clearance, bucket at 45 degrees – 8 ft. 4 in. (2.49 m)
Reach at full height, bucket at 45 degrees – 35.5 in. (902 mm)
Digging depth below ground, bucket level – 4.2 in. (107 mm)
Distance from front axle centerline to bucket cutting edge – 82.6 in.
(2097 mm)
Raising time to full height – 4.6 sec
Bucket dump time at maximum height – 1.4 sec
Bucket lowering time (power down) – 2.4 sec

Tires

Front Tires – 11L-16
Front Tires – 12.5/80-18 / 14.5/75-16.1
Rear Tires – 19.5L-24
Rear Tires – 21L-24

JD 410G Dimensions

Operating Weight (2WD ROPS) – 15,000 lbs (6804 kg)
Operating Weight (4WD, cab, extentable dipperstick) – 18,500 lbs (8391
kg)
Wheelbase – 82.7 inches (210 cm)
Length – 287 inches (728 cm)
Width – 90 inches (228 cm)
Height (ROPS) – 111 inches (281 cm)
Height (cab) – 111 inches (281 cm)
Turning radius with brakes – 13 ft. 3 in. (4.04 m)
Bucket clearance circle – 31 ft. 8 in. (9.65 m)
Steering wheel turns, lock to lock – 3.3
Ground clearance – 14 inches (35 cm)

Leave a Comment